sheetmetal 是什么意思

sheetmetal的中文意思是: 金属板

sheetmetal例句大全

  1. The design of double-sheetmetal unit for disc double-sheetmetal steam trap

    圆盘双金属片式蒸汽疏水阀双金属片组件的设计

  2. clip cabling to sheetmetal bracket.

    将线缆卡到钢板支架上。

  3. Ensure that sheetmetal clip is fit ted correctly.

    确保正确安装了金属板卡子。

  4. fit the sheetmetal brace under the radiator.

    安装散热器下的金属板撑杆。

  5. remove upper screw on sheetmetal holder.

    拆下钢板架上部的螺钉。

  6. The hooks must be positioned over the sheetmetal seam and the side sheetmetal holder must enclose the

    挂钩必须置于钢板接缝上方,且侧钢板架必须将纵梁围起。

  7. Loosen sheetmetal reinforcement around the throttle housing .

    松开节气门壳周围的金属板加强件。

  8. Install diagonal braces and sheetmetal cross member.

    拆下杆和薄壁横梁。

  9. check both sheetmetal clipsand both fastening parts, replace if necessary.

    检查两个钣金卡子及两个紧固件,必要时应进行更换。

  10. Attach sheetmetal nut to the backrest shell.

    将钢板螺母放到靠背壳上。

  11. remove all the old sealant from the sheetmetal flange.

    从金属板法兰上清除所有旧的密封胶。

  12. Clip side cover into the sheetmetal clip of the a-pillar.

    将侧盖卡入a柱的金属夹。

  13. Fasten the front end with the sheetmetal screw s.

    使用钣金螺钉紧固前端。

  14. Do not put it on the sheetmetal part!

    不要将它放在钣金件上!

  15. Only apply body sealant to primed sheetmetal parts.

    只能将车身密封胶涂抹在涂过底漆的钣金件上。

  16. Secure the line with a new sheetmetal clip.

    用新的钢板夹固定控制管路。

  17. check sheetmetal nuts for deformation, replacing if necessary.

    检查钣金螺母是否变形,必要时更换。

  18. fit tension cable to the shaped sheetmetal part.

    将张紧拉线安装到成型钣金件上。

  19. Unclip sheetmetal clips on carbon canister with a screw driver.

    使用螺丝刀松开碳罐上的金属夹。

  20. Press down new seal all around the sheetmetal flange.

    将新密封件沿金属板法兰四周按紧。

  21. Tighten the seat rail cover with the sheetmetal screw s.

    用自攻螺钉拧紧座椅轨罩。

  22. remove sheetmetal support for coolant pipes in the centre tunnel.

    拆下中央通道中冷却液管的钢板支架。

  23. To do so, fit the sheetmetal ring and tighten using the key.

    为此,先安装钢片环并使用扳手将其拧紧。

  24. Fasten the front end with the sheetmetal screw s and the spacer sleeves.

    用自攻螺钉和间隔垫圈紧固前端。

  25. To do this, fit the sheetmetal ring and tighten using special key.

    为此,安装钢片环并用专用钥匙拧紧。

  26. Move throttle housing into installation position and place sheetmetal reinforcement around the throttle

    将节气门壳移动到安装位置并将金属板加强件置于节气门壳周围。

  27. When doing so, do not forget any of the sheetmetal holders under the screw s.

    进行此操作时,切记不要忘记螺钉下的任何钢板架。

  28. All the tool makers, skilled machiners ( machinists ), sheetmetal workers, assembly-shop workers and

    所有的车工、机器操作工、钣金工、装配工和钳工属于一个工会。

  29. When the side radiator is remove d, remove the sheetmetal clips and washers for the bracket.

    当侧散热器拆下时,拆下托架的钢板架和垫圈。

  30. Guide the bulb into the sheetmetal holder at an angle and press it to the side.

    以一定角度将灯泡导入钢板架,并将其压向一侧。

  31. affix front spoiler to the retaining strip and fasten it with the sheetmetal screw and spacer sleeve.

    将前扰流板固定在束带上,用自攻螺钉和间隔垫圈固定。

  32. The completed assembly drawings ( including the sheetmetal ) are shown below along with all applicable

    已完成的装配图(包括钣金)如下以及所有适用的角度和层面。

  33. The sheetmetal brace should be installed first, then the diagonal brace and finally the rear-axle support

    应首先安装金属板撑杆,之后拆下杆,最后安装后轴支架。

  34. The Required sheetmetal clips listed in the table below must be used, depending on the vehicle equipment

    根据车辆设备不同,必须使用下表中列出的所需的金属板卡子。

  35. These holes, which are drilled through all three sheetmetal parts, will be used as an optical installation

    将三个钣金部件全部钻穿的这些孔将在以后安装前侧部时用作安装的视觉参照。