engine bracket 是什么意思

engine bracket的中文意思是: 发动机支架

engine bracket例句大全

  1. remove engine carrier bracket downwards.

    从下面拆下发动机托架支架。

  2. left engine mount bracket lower bolts

    固定支架,固定挡块左引擎固定支架下螺栓

  3. Fasten engine carrier onto the bracket.

    将发动机托架紧固到支架上。

  4. Remove engine from the mounting bracket.

    从固定支架上拆下发动机。

  5. The clamping apparatus comprises a base and an engine mounting bracket fixed on the base, wherein, the

    包括底座和固定在底座上的发动机安装支架,在发动机安装支架上安装有直角支架;

  6. In general, engine accessories is installed in the engine through its bracket.

    发动机附件一般通过其支架连接安装在发动机上。

  7. Cause analysis on Fracture of Engine Front mounting Bracket

    发动机前安装支架断裂原因分析

  8. Finite element analysis for engine bracket of special vehicle

    特种车辆发动机支架模态分析

  9. Lower engine with lifting fixture while aligning engine support insulator assembly into sill bracket

    用提升装置降下引擎,同时将引擎支座绝缘体总成对正,放入横梁托架总成内。

  10. Forming Process and Design of Bending Die for Engine Bracket Lower Plate

    发动机支架下板成形工艺及弯曲模设计

  11. work on bending forming technology of hinge bracket of car engine hood

    轿车发动机罩铰链支架弯曲成形工艺研究

  12. Study on Topology Optimization of Engine accessory Bracket under Multiple Loading Cases

    发动机附件支架多工况拓扑优化研究

  13. calculation and analysis of diesel engine rocker shaft bracket s using ANSYS software

    用ANSYS软件对柴油机摇臂轴座进行计算分析

  14. Design and Simulation of Fracture Splitting Machine Tool for Bearing Bracket of Engine Crankcase

    发动机缸体曲轴轴承座裂解机床设计及仿真

  15. Optimized Design for Structural Strength and Lightweight of Engine Bracket of an Armored Vehicle

    某型装甲破障车发动机支架结构强度与轻量化优化设计

  16. By analyzing the forming process to engine bracket lower plate, and introduced the design of bending

    通过对发动机支架下板成形工艺的分析及其弯曲模结构的介绍,总结了几种控制回弹的措施,解决了发动机支架下板回弹难以解决的问题。

  17. The Process Planning about Production Line for diesel Engine Main Bearing Caps and Injection Pump Bracket

    柴油机主轴承盖、喷油泵支架生产线工艺规划

  18. The materials used in space truss structure of aerospace plane engine thrust bracket are usually alloys

    航天发动机推力支架空间桁架结构通常采用金属材料。

  19. The gasoline generator sets consists of the gasoline engine motivity, generator stator & rotor, assembly

    汽油发电机组由汽油机动力、发电机定转子、安装支架、面板及电器件等组成(见图1)。

  20. Hence accelerate the development and ap-plicantion of nonmetal bracket, ceramic bracket and transparent

    于是就有了非金属托槽的开发和应用,常用的有陶瓷托槽和透明树脂托槽。

  21. Finally, the position adjusting bracket of extensionable fishing rod with multi sections is positioned

    在前或后杆架的固定架上或套置伸缩式多节杆架的调位支架。

  22. Position the lower suspension arm at the axle bracket and rear bracket.

    把下端悬吊臂放在车轴支架和后侧支架上。

  23. The bracket came loose.

    托架松了。

  24. Current regulator contact bracket

    电流调节器接角点托架

  25. Install cables into the cable bracket and insure retainers are seated in the bracket.

    将钢缆安装到钢缆支架且支架中的扣件务必啮合。

  26. When undoing the rear water drainage bracket, the bracket is destroyed and must be replaced.

    拆下后排水管支架时,支架会损毁,并且必须更换支架。

  27. Remove bracket with actuating elements.

    将执行元件连同托架一起取下。

  28. NHK fire resistant pipe bracket ;

    NHK耐火管托;

  29. Fasten bracket strut for pedals.

    紧固踏板的托架支柱。

  30. Rivet the support on the bracket.

    在托架上铆接支架。

  31. Open line bracket and remove line.

    打开管路托架并拆下管路。

  32. Unscrew parking brake at bracket.

    旋开支架上的驻车制动器。

  33. Install bracket for hardtop mount.

    安装硬顶支座的托架。

  34. Clip cabling to sheetmetal bracket.

    将线缆卡到钢板支架上。

  35. Insert bottom microswitch in bracket.

    将底部微动开关插入支架中。

  36. The motor bracket is arranged in the bracket chute, so that the mounting and dismounting are convenient

    电机支架设在支架滑槽内,这样拆装方便。

  37. To do this, release the support bracket sleeves and carefully pull out of the support bracket.

    要执行此操作,请旋开支架套管并将其小心地从支撑托架上拉出。

  38. Please check the windlass attached bracket.

    请检验锚机旁撑。

  39. Note that you need an exclamation point after the opening bracket, but not before the closing bracket

    要注意感叹号是写在前尖括号之后,而非后尖括号之前。

  40. People in the high income bracket.

    属于高收入等级的人。