entrance bushing 是什么意思

entrance bushing的中文意思是: 入口衬套

entrance bushing例句大全

  1. Hoist pump drive shaft bushing

    起重机油泵传动轴衬套

  2. Thrust disc is made of steel and thrust bearing bushing surface is made of plastic bushing.

    推力盘为钢制材料制成,推力轴承瓦面为塑料瓦材料制成。

  3. Master cylinder bushing at the clutch pedal.

    离合器踏板处的总泵衬套。

  4. Crankcase cam gear bushing grain drive shifter

    曲轴箱凸轮传动轴衬套

  5. Do not remove collar bushing with valve under pressure.

    在阀门处于压力状态下,不要拆卸轴环。

  6. Development of Ceramic Bushing for Spindle of Machining Center

    加工中心主轴陶瓷衬套的研制

  7. Rep air on flange of air hammer piston guide bushing

    空气锤锤杆导程法兰的修复

  8. The extra long bushing offers excellent load bearing characteristics.

    额外的长期套管提供出色的承载特性。

  9. machined bonnet stem bushing provides back-up stem seal.

    后座-经过精密加工的阀盖阀杆衬套实现后座阀杆密封。

  10. For ganged version, the bushing is metal brass with out plating.

    若是多组型产品,轴套是无镀层的黄铜。

  11. Differential drive pinion cage bearing crankcase cam gear bushing

    差速器主小齿轮轴承罩曲轴箱凸轮传动轴衬套

  12. A brass bushing or a lining for a bearing.

    黄铜轴衬或轴承衬里。

  13. Study and Discussion of Noble Metal Bushing Current collector

    贵金属轴瓦型集电器研究与探讨

  14. Chromium-plated thin-walled steel cylinder liner front spring eye bushing

    钢质薄壁镀铬汽缸衬套前钢板弹簧卷耳孔衬套

  15. Insert bushing into the bore of the main bow.

    将衬套插入主撑架的孔中。

  16. Insert lower half of bushing into square hole in crossmember.

    将衬套下半段放入横梁的方孔。

  17. Application of Silicon Rubber Compound Bushing in Circuit-breaker Capacitor

    硅橡胶复合套管在断路器电容器上的应用

  18. Premature wear failure analysis of track pin bushing in swamp bulldozer

    湿地推土机履带销套的早期磨损失效分析

  19. The long er bronze rod bushing provides a maximum load bearing support .

    时间越长青铜连杆衬套提供最大承重的支持。

  20. Influence factors in oxygen index test of fire retardant PVC bushing

    阻燃PVC电工套管氧指数测定中的影响因素

  21. Ageing Caused by Partical Discharge in the Bushing of Bakelized Paper Insulation

    胶纸套管的局部放电老化

  22. Bend the bushing tabs so that they are contacting the leaf spring.

    弯曲衬套接头以便接头能与叶片弹簧接触。

  23. The frame applies the square and hollow iron pipe so that the height and width of the vertical bushing

    该框架采用方型空心铁管,两侧竖向、横向套管均可伸缩调节高度、宽度。

  24. The author introduces starter bushing type, installing position and fit clearance ; lists its failure

    介绍起动机衬套的种类、安装位置、配合间隙,例举因衬套引发故障的现象、故障点及排除方法,列表给出了市场上90%型号衬套的适用车型。

  25. Analysis and improvement of polarity test in bushing current transformer of shunt reactor

    并联电抗器套管CT点极性方法的分析与改进

  26. The grading capacitor chiefly consists of body, metal expanders, impregnant and porcelain bushing.

    断路器电容器由器身、扩张器、浸渍剂和瓷套等零部件构成。

  27. The piston bushing materials is the key problem of automobile engine technology.

    活塞衬套材料是发展汽车发动机技术的关键问题。

  28. Rod Bushing: Large bearing area provides maximum rod support side load protected.

    连杆衬套:大型轴承领域提供了最大的棒支持并行负载保护。

  29. The insulation could be characterized by measuring the leakage current of bushing.

    通过测量断路器环氧套管的泄漏电流来表征绝缘特性。

  30. Discussion on Earthing Modes of High Voltage Bushing End Shield in Power Transformer

    电力变压器高压套管末屏接地方式问题探讨

  31. A wear-resistant bushing is sheathed on a tail end sleeve end tube, and a flange of the bushing is pressed

    尾端套管上穿套一个耐磨轴衬,轴衬凸缘被压在尾翼板和尾端套管之间。

  32. Analysis of Transformer Partial Overheat Fault Caused by Lead Wire Defect in Bushing

    套管引线绝缘缺陷导致的变压器局部过热故障分析

  33. Tighten leaf spring press until bushing flange bottoms solidly against leaf spring eye.

    上紧叶片弹簧加压机直到衬套凸缘的底部扎实地抵住叶片弹簧的孔眼。

  34. After each time's well logging, open the upper bushing and the lower end cap.

    每次测完井后,打开上护帽、下堵头。

  35. The steel retaining plate has two functions , retaining the bushing and preventing rod rotation.

    固定板的钢具有两种功能,保留套管和防止杆旋转。

  36. In some instances the reinforcement can be achieved using small aluminum tube as bushing.

    在一些例中钢筋能被达成以小的铝管作为桥衬。

  37. A metal screening can is provided between the weld flux and the insulating porcelain bushing.

    熔体与绝缘瓷套之间还设有金属屏蔽罩。

  38. Closely held tolerances on the plate and bushing allow a precise fit to prevent rotation.

    紧紧举行板套允许公差和精确的适合防止旋转。

  39. The reference spectra was the signal obtained by coupling the two fibers with a splice bushing.

    参考光谱是通过将两个纤维与一个接合套筒耦合后获得的信号。

  40. This procedure MUST be followed when installing a new bushing or seizure to shaft may occur.

    安装新衬套时,必须遵循本程序,否则驱动轴可能滞塞。